Models > WED96HEAW1 > Instructions

WED96HEAW1 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the WED96HEAW1
106 - 120 of 608
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Victor from ORANGE, CA
Parts Used:
4392067
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Dryer was not running as fast as normal, belt was squeaking loudly
The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Maple Valley, WA
Parts Used:
279787
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Dryer motor bearings failed. Motor wouldn't start.
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
8 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from DINUBA, CA
Parts Used:
4392067
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Repair video made it easy
Just follow the repair video, it was easy!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOANNA from FLATONIA, TX
Parts Used:
WP3392519
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Replacing the gas ignitor
Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from CAMARILLO, CA
Parts Used:
4392067
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JoAnn from ANTHONY, FL
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Had heat, but clothes did not dry.
Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from Yucaipa, CA
Parts Used:
W10837240, 661570
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The bearing on the idler pulley went bad, squealing
Took the dryer apart and replaced the idler pulley with bracket and the drive belt
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Travis from GARRETT, IN
Parts Used:
W10837240
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Very loud squeaking!
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gus from RIVERSIDE, CA
Parts Used:
661570
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Belt Broken
Watched video & took my time. It went easy
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from KENNETT, MO
Parts Used:
WP8577274
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Coal Hill, AR
Parts Used:
WP3392519
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
BLOWN THERMAL FUSE
I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from TINLEY PARK, IL
Parts Used:
W11758174
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old lint screen didn’t have the felt and my dryer kept filling up with lint
Took old screen out and installed new screen
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
bryan from somerville, MA
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
dryer would run, but not heat
removed the rear panel to gain access to the internals of the dryer, removed the one screw that retains the fuse, out with the old and in with the new.
delivery of the part was 2 days sooner than expected.
could not have been a simpler process!
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bobbie from BEND, OR
Parts Used:
49621
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
No leveling feet on dryer.
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from CALIFORNIA, MO
Parts Used:
661570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broken belt
Disconnect gas line and vent hose,removed top and back covers to install belt.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WED96HEAW1
106 - 120 of 608