WED87HEDC0 Whirlpool Dryer - Instructions

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

very easy

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

Remove top,front and panels.change thermal fuse and outlet thermistor.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better

Took top lid off dryer ,replaced control, very happy it ran perfect thank you

Just follow the repair video, it was easy!