WED8500DC1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rory from LEESBURG, VA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KENNESAW, GA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
My dryer made squeaking noise when rotating.
I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from LEBANON, PA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Loud squealing noise during operation
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TROY, AL
- Parts Used:
- WPW10512946, WPW10359272, WPW10314173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Drum support roller making very loud noise
had to take front off of Dryer then was able to replace drum roller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from ORANGE, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was not running as fast as normal, belt was squeaking loudly
The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curtis from STOCKBRIDGE, GA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from MAGNETIC SPGS, OH
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pulley bad
pull the back off and replace the pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from CLIFTON, NJ
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Pulley wheel broke apart
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CONRAD from Lake Toxaway, NC
- Parts Used:
- WPW10739349
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer would not turn on
unplugged dryer, removed screws from top back plates, removed screws from control board unhooked connectors and put them on new board. Put screws back in and plugged dryer in. Dryer turned on and works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candido from GREENVILLE, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TULELAKE, CA
- Parts Used:
- WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this instruction helpful to you?
Thank you for voting!