WED71HEDW0 Whirlpool Dryer - Instructions

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

Lint can build up inside the dryer, and can cause a fire in EXTREME cases. If your model has a back panel that exposes the entire chute, this job is much easier. Unscrew the chute from the machine to remove it. Inspect and clean all the lint out, especially the bottom, next to the fan blower. The other version machine has a panel at the top that is welded on. Remove the two screws at the top corner of the rear bulkhead, where the chute is. Gently pull this inner panel away to free the top of the chute from the rear top panel. Then pull the chute down and out. Follow the reverse to complete the job.

Followed the instructions on your video.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.

I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!

Dryer is on a pedestal. Opened drawer and removed two 1/4 inch screws on bottom panel of dryer front. Panel drops down and exposes the dryer exhaust where thermistor is located. Removed two spade connector wires and removed two 1/4 inch screws. Installed new thermistor and reversed procedure. For the moisture sensors I used a phillps screwdriver and stuck my head in the dryer and removed the lint screen assembly (3 screws). Removed the spade wire connectors and used a straight blade screw driver to remove the moisture sensor. Installed the new sensor and re-installed the lint screen assembly in the reverse of removal. All very easy - just took 30-45 minutes total.

My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.

First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.