WED71HEDW1 Whirlpool Dryer - Instructions

removed back panel located heater coil assembly, bottom left of dryer. removed back screw holding heater coil assembly, difficult because it was two feet back where i was. screw was small 1/4 inch. removed wires to thermostat and fuse to remove heater assembly. removed thermostat and thermal fuse, installed new thermostat and thermal fuse. installed new coil. replaced cover to coil assembly. attached heater coil assembly back to its place inserted screw and replaced panel. threw in some wet towels started dryer and worked perfectly.

Dont believe that '1.8 days average delivery' time. if you need to parts in days, get them delivered overnight. Otherwise it was very easy to seals, rollers and belt. Only advise is on the seals. you might want to sort of stretch them out a bit so they are easier to slip on because once you have the glue on there it is harder (and messy) to be stretching them on

Had to unstack the unit took it apart and replace the rollers,Belt and Idler Pulley It was the pulley making the noise but I had it a part and for the cost I replace the rollers and the Belt the Job was easy The Washer and Dryer are Great we run about 2 Loads a Day

Repair was fairly easy, lots of screws to remove but the instructions in the online repair manual were very clear. Lots of stuff to remove (top, front, drum, etc.) but not too challenging. Only tough thing was disconnecting one of the connectors on the electronics board, had to use a pair of pliers to squeeze the part to get them separated. Once I had it all apart it was very easy to replace the wheels and the belt. Putting it back together was easier than taking it apart.

Our dryer got so loud after running for a few minutes that you couldn't even have a conversation in the same room. After researching for possible causes, I decided to go with new drum wheels. I purchased the Dryer Repair Kit to save a little money and it gave me a new belt and tension wheel as well (since I was going to have it apart anyways). After taking everything apart and vacuuming out all the lint from inside, I noticed that the blower wheel was broken. No idea how that happens but something must have gotten in there and broke 2-3 fins and cracked the rear side. I replaced the parts that came with the kit and proceeded to put it all back together. Started it up and it was worse than before. Quickly ordered the new blower wheel and that fixed the problem. Back to a "quiet" dryer. I probably didn't need the Kit after all, but the drum wheels were a little worn and I had it apart anyway.

The videos really make it easy. I put my laptop on the washer next to my dryer and proceeded step by step. I also found the video that mentioned about the screws that may come loose on the baffles. I found several loose screws on the baffles which I tightened and I also found the Drum hole plug loose, so I also tightened the plug. Reassembled the unit and has been working like new since.

Our Dryer was no longer heating, upon opening the bottom of the dryer, there was a large amount dryer lint in the bottom. I cleaned it out and found the coil was no longer heating. Order parts from Partselect.com The parts were a perfect match! Identical to the original parts. The repair was simple once I decided to remove the back of the dryer. A lot of screws but with a driver it went quickly.

My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.

First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas

After removing the back & top of the dryer,I determined the noise was coming the idler pulley.I went online w/ model # & found Partselect.com.I ordered the dryer repair kit (at my door in 3 days) which included all the rollers,idler pulley, belt & hardware.It was an easy job to do even tho instructions were for top control panel model (mine is a whirlpool duet- front control) I did try using silicone lubricant on idler pulley, which worked to quiet dryer for a couple days so my wife could use it while I was waing for parts.Two thumbs up to Partselect.com,I will be purchasing all my appliance repair parts from them..I own all whirlpool stainless steel appliances that have been very reliable,but it's nice to know I have Partselect to fix problems as needed.

Replaced with parts orded worked fine for2 hours and quit heating again

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.

Dryer is on a pedestal. Opened drawer and removed two 1/4 inch screws on bottom panel of dryer front. Panel drops down and exposes the dryer exhaust where thermistor is located. Removed two spade connector wires and removed two 1/4 inch screws. Installed new thermistor and reversed procedure. For the moisture sensors I used a phillps screwdriver and stuck my head in the dryer and removed the lint screen assembly (3 screws). Removed the spade wire connectors and used a straight blade screw driver to remove the moisture sensor. Installed the new sensor and re-installed the lint screen assembly in the reverse of removal. All very easy - just took 30-45 minutes total.

I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!