3RLER5437KQ1 Whirlpool Dryer - Instructions

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!

Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.

Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.

Old door catch came out, new one slipped in. All works great.

I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.

My dryer timer would run through the heat cycle and move in to the cool down cycle. It would not move past the cool down cycle, and would not shut off automatically. I tried replacing the Thermal Fuse first, since I'd already removed the back panel to diagnose the problem. There was no change - the dryer did not shut off automatically. Next, I removed the back cover to the timer console. The Timer Power Resistor looks like a black circle and a rectangle joined together. It was attached to the back of the on/off switch by a single hex head screw, and the resistor has orange and black wires attached. The replacement Power Resistor doesn't look like the resistor that was in my dryer. It is rectangular in shape with 2 male spade connectors. I attached the orange and the black wires to the new power resistor. I started the dryer and it went through a full heat/cool down cycle, and automatically shut off with the end of cycle buzzer sounding. Total part replacement time was about 10 minutes.

Safety First - I unplugged the power source. I removed the console by simply removing several screws. However because the nut fastening the resistor was in a really tight spot and I had little room to work, I decided to remove several screws from the back of the console to open it up. (This step is not necessary - but for me, it just made the job go quicker). I was then able to use my ratchet/socket set to remove the nut from the resistor. I then attached the wires from the timer to the new in-line resistor. I closed up the console, re-attached it to the dryer and DONE!!! The dryer works fine!!! By the way, the set is 25 years old. I initially thought it was the timer itself but after explaining the problem to Rebecca at this iste , she quickly identified the problem as the timer power resistor. Many thanks Rebecca??

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.