WED6400SG0 Whirlpool Dryer - Instructions

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

replaced rollers, belt and pulley. Video was very helpful

flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.

pushed the broken catch into the door and snapped the new one back in. Works perfectly!

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Taken dry a part remove the belt and then the idle replace with new one taken about 30 minutes.

I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.

This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.

Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.

My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.