LDR3822HQ0 Whirlpool Dryer - Instructions

replaced internal dryer filter housing

Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business.

First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...

I remove the lint trap and the two screws that held the top down. Next to unscrew the two screws that holds the door switch. I prized the top up with a screwdriver . I unplugged the door switch and plugged in the new one. I inserted the switch into the door and replace the screws. I snapped the top back into place and replace the screws in the lint trap. I close the door and turn the dryer on and it worked. I followed the directions you provided on line. They were very easy to follow.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

First unplug unit to avoid shock. Using a flap blade screwdriver lift the front corners of the top. Unplug the switch located on the right side in the front. Remove two screws holding the switch in place. Remove old switch and reverse to install new switch. Entire project took less than 10 minutes. Oh yes the wife was so happy she made me a dish of fudge brownies. :)

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

Disassembled dryer, removed tumbler, replaced drum support rollers

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

just replaced parys

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business