GEQ8858KQ0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Betty from Erie, PA
- Parts Used:
- 279457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HAGERSTOWN, MD
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from PALM BCH GDNS, FL
- Parts Used:
- WP697813
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter seal worn out
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Santa Ana, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was broken
Just replaced the old lint filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from NORTH OLMSTED, OH
- Parts Used:
- WPW10359272, WPW10314173, W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench set
Dryer made squeaking noise, then more of a rumbling noise.
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from TROY, MI
- Parts Used:
- WP3406725
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Timer failed, needed replacement.
Unplugged the dryer from the electrical outlet. Simply removed the screws holding the long plate behind the dryer controls. Took two screws out that attached the failed timer to the dryer. Was careful to pull wiring out of the failed timer one wire at a time, replacing the wires into the new timer so as to be sure the wires were attached to the new timer in the right sequence. Some of the wires were difficult to remove from the failed timer, needed to use a pliers or a screw driver to remove some of the wires. Attached the new timer to the dryer with two screws as the failed timer had been attached. Replaced the back panel to the dryer & plugged the dryer back in to the electrical outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gay from Apple Valley, CA
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum would not spin to drain water
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LEXINGTON, NC
- Parts Used:
- WP3398094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer would not run.
After checking the temperature safeties, I replaced the Push-To-Start switch. This did not solve my problem, so I replaced the Timer Switch assembly, which did solve my problem. Both switches are very simple to replace. Unplug the dryer, use your nut driver to remove the 6 screws holding the back control cover. For the Start switch, remove the control knob, remove the 2 screws holding it it. Unplug the wires, turn the switch housing 1/4 turn clockwise, and remove it from the opening. Reverse the process to install the new switch. For the Timer Assembly, just a bit trickier. Remove the knob, remove the 2 screws holding the assembly. Unlike the Start switch, the Timer Assembly has multiple wires. Pull the old timer assembly out, and, one-by-one, move wires from the old Assembly to the new Assembly, being sure to land them on the proper post. Once you have done this, return the Assembly to the mounting hole. A very simple repair. Even though I spent $160 chasing the problem, I still came out cheaper than calling a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Garland, TX
- Parts Used:
- 280114
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken Drum Belt
Just like the video, just followed the video
Thanks,
Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CREST HILL, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Idler pulley seized
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from SOUTHAMPTON, PA
- Parts Used:
- 279769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer ran but without heat.
Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the Thermal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from VALDOSTA, GA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was squealing
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CHICAGO, IL
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Very loud squeaking noise
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Was this instruction helpful to you?
Thank you for voting!