LDR3822PQ2 Whirlpool Dryer - Instructions

First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure solid installation and good ground. Bottom pops in but took a bit of finagling.

Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Disassembled dryer, removed tumbler, replaced drum support rollers

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

I just changed for the new one! 2 seconds.