Models > CSP2760TQ3 > Instructions

CSP2760TQ3 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the CSP2760TQ3
121 - 135 of 687
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Denise from LOGANVILLE, GA
Parts Used:
WPW10237959
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Broken dryer door switch
Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carla from Del City, OK
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
dryer suddenly stopped working
this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from CARY, NC
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from BENZONIA, MI
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Screen ripped
Dropped new filter in.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
rolando from round lake beach, IL
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
dryer would turn but won't heat up
removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dwight from charleston, SC
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
dryer would not come on, light still worked, timer still ran
I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from Licking, MO
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Dryer would not blow hot air
I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Cherry Hill, NJ
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The problem was the dryer wouldn't heat up (gas). Would run but just not heat up.
So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glen from Covington, LA
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
timer runs but dryer wont start (fuse was not closed)
Took off the backplate of dryer, replaced fuse, done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james petrie from Stoughton, WI
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
no heat in the dryer
after removing the back panel (5 screws) i replaced the heating element, (about 15 minutes, after vacuuming all of the lint and dog hair), replaced the panel, but still no heat. removed the back panel again, and replaced the thermal fuse. (2 screws, 5 min.) still no heat, so on to the thermostats. (there are 2, both in easy reach). i replaced the one in the heating element housing first, as this made sense. (it has a red stripe across it, so they can't be confused), replaced one connector, which the new part requires, buttoned it up, and presto!! the dryer works just as new! all told, i have less than 100.00 with all of the new parts. the longest part of the whole thing was cleaning all the lint and debris out first, which you absolutely must do
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from San Jose, CA
Parts Used:
WP3392519
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
dryer stopped working
How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mary from Maple Plain, MN
Parts Used:
WP3392519
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Dryer was totally dead, had power to the outlet.
I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PAUL from ARLINGTON HEIGHTS, IL
Parts Used:
WP3392519
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer wouldn't heat
It took me 5 minutes to find PartSelect's site, read the comments about the most common problems and identify the solution. The exploded views were a great assist, as it wasn't obvious where the thermal fuse is located or which access panel to remove.

It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.

A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.

I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.

PS Drying time has decreased by 30-40% since the repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevan from Ocean Springs, MS
Parts Used:
WP3392519
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Dryer wouldn't turn on.
First I pulled the dryer away from the wall, after which I disconnected the power and dryer vent. I then removed the eight screws holding on the back of the dryer. Next, I disconnected the two wires to the part and unscrewed the mounting screw. I then removed the bad part, replaced it with the new part, and reversed the above steps.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daryl from LAKE STEVENS, WA
Parts Used:
WP3392519
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Blown fuse
R&R. Simple!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CSP2760TQ3
121 - 135 of 687