WGD80HEBW0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from HANOVER PARK, IL
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
i exchange thermal fuse
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from ROCHESTER, NY
- Parts Used:
- 279311
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer running and no heat
Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manny from ODESSA, TX
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Dryer would not start!
Unplug unit first.
Took the front cover off the front of dryer below the door.
Took the front cover off the front of dryer below the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TULELAKE, CA
- Parts Used:
- WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MONA from SHAMROCK, TX
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not start.
I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Baden, PA
- Parts Used:
- W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Squealing when running
You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Bainbridge, PA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dryer would shut off mid way through cycle and give an E1 error code
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annde from JEFFERSON CTY, TN
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dryer was very loud and sounded like it was scraping
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELMA, WA
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dryer
Ezee pezee lemon squeezee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Colorado Springs, CO
- Parts Used:
- WP3387223
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
not drying completely on the automatic settings
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from GROVELAND, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squealing when the dryer was running...especially on start up.
Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from JACKSONVILLE, FL
- Parts Used:
- W11758174
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The screen in the lint filter was broken
Since it was a dryer filter, it just had to be put in the dryer. Works GREAT!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Winthrop, NY
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer would not operate
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candido from GREENVILLE, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this instruction helpful to you?
Thank you for voting!