WGD9371YL0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Earl from Santa Ana, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was broken
Just replaced the old lint filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HAGERSTOWN, MD
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from Port Arthur, TX
- Parts Used:
- 279311
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No heat, would not light because igniter burnt out
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two screws. Plug in dryer and there you go drying clothes again. Wife all happy again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from NORTH OLMSTED, OH
- Parts Used:
- WPW10359272, WPW10314173, W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench set
Dryer made squeaking noise, then more of a rumbling noise.
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Long Beach, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
No heat...
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STONE CREEK, OH
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer drum turned hard because rollers were worn
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from VALDOSTA, GA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was squealing
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this instruction helpful to you?
Thank you for voting!
Dryer too hot
I replaced both the thermal fuse and the thermistor at the same time. That seemed to fix the problem; but after a couple of days the dryer would not start. When pushing the Hold to Start button, the dryer just gave one beep and would not start. I did a resistance test on the old thermal fuse, and it was OK; so I put the old thermal fuse back in and the dryer works. Evidently, it was just the thermistor (thermostat, internal bias) that was broken. Both are very easy to change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Garland, TX
- Parts Used:
- 280114
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken Drum Belt
Just like the video, just followed the video
Thanks,
Thanks,
Was this instruction helpful to you?
Thank you for voting!
Annoying loud metal to metal screeching noise.
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Macomb, MI
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Whirlpool Gas dryer, run but no heat
I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canyon Country, CA
- Parts Used:
- 279311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The dryer would not heat up
After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...
Was this instruction helpful to you?
Thank you for voting!