3LCED9100WQ1 Whirlpool Dryer - Instructions

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I checked the motor to make sure it turned freely but it didn't so I knew it was bad, your online instructions made it so easy for me to make the motor replacement, if I ever need any appliance parts ever again .....you can bet I'm buying them from you. I purchased the motor for about 40% less then what it was retailed locally.

Repair went well your video was a great help. The motor was hard to disconnect from the blower and fan side.The shaft that you hold with the adjustable plier was hard plastic type of material and wanted to keep slipping and the edges wanted to round off and not hold in the adjustable pliers. I had to use a small pipe wrench with teeth to break it loose. The only other problem was the ground screw in the new motor had an odd type of head on it and took a special type of nutdriver attachment to loosen it and attach the ground wire to the new motor.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.

Simply installed the piece and I was done. Took 10 seconds.

My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.

I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

Popped out the old door catch kit and replaced it with the new one! Easy!!

Easy manually

All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!