WGD6400SG1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ryan from Livonia, MI
- Parts Used:
- 279834
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
dryer would not continuously heat, and took several cycles to dry clothes. The flame would ignite and heat the dryer at first, but then would ignite and go out quickly for the rest of the cycle. I tried the thermostats first with no luck.
I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wires connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monique from Mission Viejo, CA
- Parts Used:
- 279834
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
My dryer only heats up at the beginning of cycle so my clothes will not dry.
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Maryville, TN
- Parts Used:
- 49572A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
cocverting natural gas to propane gas
removed burner installed propane orfice and kit as per instruction sheet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Akron, OH
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dyer drum doesnt turn
It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Oceanport, NJ
- Parts Used:
- WPW10111905
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer door wouldn't 'latch' closed.
took off about 8 screws, opened door into it's front & back parts, popped out the old/broken door catches and re-inserted replacements. Only 1 is needed, but this is the 2nd one to break. The first time a repairman switch the un-used from right side to left. (there are 2 so the door can be hung left or right opening)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Tucson, AZ
- Parts Used:
- WP8577274
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Unit would shut down in the middle of cycle and flash E1 trouble code
Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!
Was this instruction helpful to you?
Thank you for voting!
Dryer would dry for 5-10 minuets then no heat
I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Bonners Ferry, ID
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not heat up.
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rex from streator, IL
- Parts Used:
- 279311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no heat
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Saint Clair Shores, MI
- Parts Used:
- 8547174
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer making very loud noises!
First unplug the dryer.
Remove the lint filter.
Remove two(2) screws by the filter.
Use a screwdriver to raise the top of the dryer.
Unplug wires going to the front panel (pull apart)
Remove two(2) hex head screws.
Lift front panel out of the way.
Use a light to view the pulley assembly on the bottom.
Raise the pulley to remove the drive belt.
Use a hex socket to remove one(1) bolt from the bracket.
Install new part.
Reverse order of dis-assembly.
Very Very Easy!
Remove the lint filter.
Remove two(2) screws by the filter.
Use a screwdriver to raise the top of the dryer.
Unplug wires going to the front panel (pull apart)
Remove two(2) hex head screws.
Lift front panel out of the way.
Use a light to view the pulley assembly on the bottom.
Raise the pulley to remove the drive belt.
Use a hex socket to remove one(1) bolt from the bracket.
Install new part.
Reverse order of dis-assembly.
Very Very Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Gray, TN
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Drayer Was Making Squeaking Sound
Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Lemitar, NM
- Parts Used:
- 49572A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Convert gas dryer to Propane
Received conversion kit. Removed front dryer panel,2 screws. Removed burner tube, 2 screws then removed natural gas orfice.
Installed propane orfice and repalced burner tube.
Removed regulater plug and replaced with new plug from kit using 90 degree ratchet screw driver. Approximately 20 minutes. Dryer working great.
Installed propane orfice and repalced burner tube.
Removed regulater plug and replaced with new plug from kit using 90 degree ratchet screw driver. Approximately 20 minutes. Dryer working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valerie from Elasmore, KS
- Parts Used:
- 279311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer stoped heating
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from Riley, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dyer would not heat, flame would shut off within 10 seconds
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Groveland, MA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Belt broke, dryer stopped.
Replaced the belt and the wheels supplied with the kit. I also cleaned the inside of the unit. It looks and works like new.
Was this instruction helpful to you?
Thank you for voting!