CSP2770HW0 Whirlpool Dryer - Instructions

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

Dropped new filter in.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

just followed the video directions, worked perfectly thanks

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.