WED6200SW0 Whirlpool Dryer - Instructions

Replaced thermal sensors.

Unplugged Dryer.

Removed back panel & dryer hose - About 10 screws

Removed Heating element - two screws

Followed instructions for replacing old thermal cut-off with new model (this was slightly different from original equipment - wiring modification was required) All connections were detailed in the instructions. Jumper wire and new screws included in Thermal Cut-Off kit.

Cleaned lint and dust from inside dryer.

Replaced back panel and dryer hose.

Tested dryer, works like new.

I attempted to take the back panel off the dryer only to discover all I had to do (after removing 10 or so screws) is remove the lower base plate in the front of the dryer. I also had removed the door which turned out to be unnecessary. After removing a guard in front of the heating element (2 screws) I yanked the the element housing that contained the heating element and then disconnected the 6 wires. Using my first ever, newly bought multi meter for only $9.99 from Radio Shack, I turned the dial to the infinity section and check the element for continuency. I did this by touching the meter's two probes to the element's terminals were the wires connect. The element was fine. Then I checked the two sensors the same way. The sensor furtherest away from the element's terminals didn't have a constant signal so I assumed that that sensor was bad. Well, come to find out, one sensor is open and the other in closed... only when the temp. changes do they operate by opening and closing the current. By this time I had already ordered the part so it was too late. Surprisingly, the part came in 2 days. I ordered it Sunday night and i figured it would be sent out Monday but it was already in the air Monday morning... Great service! I replaced both sensors and the dryer works like it did when I first got it.

I removed all the screws to the back panel to gain access to the inside. checked all thermostats and fuses for conductivity (0.001 ohms) resistance. noticed the thermal cut off fuse (thermostat) was showing no conductivity (infinite ohms or OL). FYI the thermal cut-off kit I purchased included both the thermal cut-off fuse(why this is called fuse is a lie its actually a thermostat) and high limit thermostat. I'm seeing alot of users purchasing these seperate but it isn't neccessary. You might need some wire strippers with a crimper though to install everything.

Remove backpanel, ohms cut off thermostat, no good, disconnet two wires from defective part and installed a new one.

I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.

The only challenging part was getting the old catch out. It can easily fall inside the door, not that this is really a problem, just leave it there. Using pliers get a good grip on the edge of the old catch and rock the top out, then pull to get the bottom out. There will now be an open hole. Align the new part with the open hole, and simply push it in. It will catch, and click into place. No tools are needed to install.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Watched a couple of you tube videos, seemed simple enough. Used multimeter to test thermostats, still good. Took off the heating element, it was visually broken. Called the 800 number, the guy who answered told me how to find the model number of the dryer. He then told me the part number and it matched what I had. Ordered, 2 days later arrived, just plugged it in and reinstalled the back covering, works great!

This was soo much easier then I thought!!! Make sure you unplug the dryer FIRST!! I removed the bolts that held the dryer back with the socket wrench. The removed the 2 screws that held the heating element in place. Disconnecting the cords was a little harder but will come off with the pliers. There is that piece of your old heating element that you need to remove to put on the new one that was hard to get off. its being held on by a metal lip and at first I couldnt figure out how to get it off, but then I just kept bending it (the metal lip) until I was able to get the piece off of it. Then just connect the wires onto the same points that your removed them from. Replace screws and back of the dryer and WaLa!!! You've just saved yourself the price of labor for an electrician.... Trust me if I can do this YOU can... My husband thought I was crazy.. I get shocked changing light bulbs but my dryer is drying a load of clothes as we speak!!!

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

I highly recommend using a multi-meter to test for continuity on the thermistors and the heating element. It will likely save you a lot of time and you can replace the correct part the first time. I found the high limit thermostat to be open. Also note that if you find the same part open, it is most always caused by another part failure or the dryer vent to be clogged up with lint. I also cleaned out the lint chamber which was in pretty bad shape and likely caused my failure. But, the parts were not expensive and were replaced while I was doing the trouble shooting. The video is excellent and if followed all will turn out ok. This is my third different appliance repair, and the parts are always in stock, the standard shipping was 7 days, and everything you need is provided.

Followed online video very easy and dryer works like new one....

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

First cut breaker off, removed wall plug, then removed back panel removed old element installed new one, had a great opportunity too clean lint from blower, and entire unit. Very good job. The video with instructions was awesome.