WED6200SW0 Whirlpool Dryer - Instructions

Good

Take front panel off with 5/16 nut driver and reach in and get 3/8 socket to remove 1 bolt off and replace idler pulley

The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.

First ordered belt and rollers Noise continued then orders tension roller. Better but still noise. Son thinks may be motor. Repair was easy just followed what you already had on line.

removed back of dryer. Pull electical connections, removed heating element. Inserted replacement element, attached electrical connections and attached dryer back. Done -easily done.

unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Dryer ran with no heat. Replaced the Thermal Fuse and when that didn't fix the problem discovered the element was burned. Easy fix except the F-disconnect fitting broke when I tried to remove it and male fitting on the heating element is 0.375 and all I could find were 0.250 F-disconnect fittings. I finally found a supplier who had a 0.375 fitting and the repair took 10 minutes after that. The online videos at PartSelect are excellent.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

Ordered new latch. Installed new latch into the dryer within one minute.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

I spent the most time researching and confirming exactly what part I needed before ordering the shipment. The illustrations and videos available on how to replace the part(s) were VERY helpful and much appreciated.

I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - and stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.

I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.

Simply checked the thermostats for conductivity and found that they were working properly. Removed the heating element to check for conductivity and discovered a broken coil. If I had the part ready to go the whole process from taking off the first screw to replacing the element to screwing on the last screw would have taken less than 15 minutes. Very simple repair that I almost paid a service technician an additional amount for something that a novice DYI'er could do.