LE4900XTM0 Whirlpool Dryer - Instructions

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.

I replaced a bad thermostat

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

just replaced parys

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Replaced lid switch, but problem still continued.

Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.