CE1750XWW1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from SAN LORENZO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
Idler pulley was frozen on the shaft.
Removed the top, front cover, drum and belt. Removed the idler pulley bracket and pressed the frozen pulley from the shaft. Cleaned the shaft and applied a small dab of anti seize and replaced the pulley. Installed all parts in reverse order. Dryer works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from HARRISBURG, NC
- Parts Used:
- 661570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
We had a broken belt.
Looked it up on YouTube. It told me to take the front panel off. I did, changed the belt, put the panel back on and it works perfectly. The part came in the time it was supposed to and it was the correct part. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Marietta, GA
- Parts Used:
- 279973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dryer stopped heating
Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from FOND DU LAC, WI
- Parts Used:
- W10837240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Loud squeaky sound at start up
Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmine from MASSAPEQUA PK, NY
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door keeps opening while operating
Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from Kettering, OH
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Door Wouldn't Shut
My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Thompsonville, MI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door catch wouldn't hold the door closed
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Laingsburg, MI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door wouldn't fasten shut
Popped the latch out and popped a new one in.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.
Was this instruction helpful to you?
Thank you for voting!