CE1750XYN0 Whirlpool Dryer - Instructions

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

It was a lot easier then I thought. Just watch the tutorial of how to fix it on this website and you wont have a problem.

Unplug from electric ? outlet. Set the meter to ohm setting, check part ,no reading. Remove old part ,check new part with meter ,get a reading of 11 or more mA. Install new part and blower cover done.

just put the new part in the door---sooo easy! THANK YOU!

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Removed front of dryer. Located thermal fuse, replaced blown thermal fuse. Reassembled.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

just replaced parys

Removed the top, front cover, drum and belt. Removed the idler pulley bracket and pressed the frozen pulley from the shaft. Cleaned the shaft and applied a small dab of anti seize and replaced the pulley. Installed all parts in reverse order. Dryer works like new again.