LG4931XTM0 Whirlpool Dryer - Instructions

Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.

Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!

Replaced coils on gas valve.

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together to save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.

Replacement fit perfectly.

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.