CEM2940TQ0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dillard C. from Vina, AL
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lance from GREENSBURG, PA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Noisy when drum rotates
Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.
Was this instruction helpful to you?
Thank you for voting!
Dryer belt worn out, rear seal worn replaced drum baffle
Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from DELHI, NY
- Parts Used:
- 279816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer runs, but won't heat.
First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAT from ALHAMBRA, CA
- Parts Used:
- WPW10512946, W10612022, 349241T, 341241
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Noisy
Asking my question on you tube they show me problems and parts to need replace and how do installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Flushing, NY
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken drive belt
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from carol stream, IL
- Parts Used:
- WP3405184
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
over-all different problems with esate.
Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Eaton, OH
- Parts Used:
- 279816
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No Heat
The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.
Was this instruction helpful to you?
Thank you for voting!
a loud, high-pitched ringing noise
Raised the top of the dryer then took the front of the dryer off. Took the drum off. Replaced the pulley and support rollers. Then, put the new belt on and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from PITTSTON, PA
- Parts Used:
- 279827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer makes squealing noise, finally the motor seized up.
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willis from GRAND FORKS, ND
- Parts Used:
- 279816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
dryer not hot enough, too long to dry.
Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diora from ROCKFORD, IL
- Parts Used:
- W10861521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wore out gasket
removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy
Was this instruction helpful to you?
Thank you for voting!
drum stopped
10 min. job, easy to do / two screws top and two inside front / remove old parts install new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from NEWPORT, NC
- Parts Used:
- WP349639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Lint Screen Was Torn.
Fit great,well please with order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from appleton, WI
- Parts Used:
- WPW10359270, WPW10359269, 349241T, WP348197, 341241, 279441
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
loud shrieking sound when it ran
nobody has said it yet so... to take a dryer apart, take the back off, pull the lint trap, remove two screws on back of the top piece. the whole top shifts forward and disengages two clips on front corners, it then tilts up and back. the front comes off next, this frees up the tub. all parts ordered replaced worn parts, though there was no smoking gun as to the source of the sound. once it was apart, it was a cakewalk. had it up and running in 45 minutes. can't see how it took others two hours.
Was this instruction helpful to you?
Thank you for voting!