WGD8127LC4 Whirlpool Dryer - Instructions

The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

Remove old filter
Vacuum out
Install new filter

Ezee pezee lemon squeezee.

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Removed the dryer door, unscrewed lint vent.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

remove 3 screws vent comes out put new part in works grate just like new a gain

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!