YWED6400SW1 Whirlpool Dryer - Instructions

Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.

Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.

Unplugged dryer from electrical outlet. Removed top panel from dryer to get instructions for location of parts. Removed front panel to get to fuse and thermostat. Had to purchase small socket wrench to access nuts because of small space and angle of difficulty. Removed both parts, and replaced with new parts. Plugged dryer back in. Tested for heat. Working properly.

The repair, replacing the thernal fuse was easy, just one screw and then remove and replace by disconnecting and reconnecting two wires. It did take a bit of time to find which part was defective. I first removed the back panel and front panel and the drum to get at the igniter and flame window. I checked continuity of these parts as well as the gas solenoids and they all checked out ok. The thermal fuse was last on my list. It read as an open circuit. I temporarily jumpered the two wires at the fuse and checked that the igniter would now heat up. I spent over one hour removing the ductwork and giving the unit a thorough cleaning with a shop vac.

How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.

I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.

The Termal Fuse did not solve the problem. Ordered a heating element so I hope its that

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I made sure air vent was clear and clean. I removed front panel of dryer unit, located fuse, removed wires, tested fuse with ohm meter, which was defective. Tested new fuse placed back in dryer reattached wires. Cleaned out inside of dryer, replaced front panel. Now works like new.

Dryer works - thanks to a new fuse. Glad I tried this before just buying a new one. Video for my model indicated the fuse was located in the back and actually it was difficult to get to in the front. So extra time was wasted trying to get to fuse in the back. Thank you for the part!

Attempt to start dryer normally. Turn timer dial to high heat setting. Press the Push To Start button. Verify plug is secure in wall outlet. Got to breaker panel to verify breaker is not tripped. (Sometimes breaker may trip but visually appear no to be tripped). Reset breaker to maker sure breaker is in the on position. Attempt to start dryer normally. If dryer did not start proceed. Get a multimeter. Remove plug from wall outlet. Slide dryer from wall. Remove exhaust duct from bottom of dyer. Use multimeter to check voltage at wall outlet. Verify 120 to ground and 208 between hot legs. Remove rear cover if main dryer unit and rear of control unit. Connect the multimeter to rear of control panel rear of push button. Turn meter to ohm setting. Push the start button to see if there is continuity. Release the button to verify no continuity. Next major part of curcuit is the thermal fuse. Look on lower left area of dryer. With multimeter in Ohm mode place the leads on the light blue wires. If no continuity replace thermal fuse

There was no heat but the dryer would operate properly in all other functions. I checked the ignitor (gas dryer) with a meter and it was okay. I traced the circut back and ended up at the thermal fuse and it was "open" I jumped it out and the dryer started to work. I knew the problem was the thermal fuse but more importantly why did it blow. Further investigation showed excessive lint in the duct. Needed to take the exhaust system apart and clean out the lint. also replaced the flexible dryer (too difficult to clean) and to make sure that I didn't over work the high/low thermostat and would be doing this repair again in the near future I replaced that also. Be careful and do not jump out the fuse and use the dryer as this will cause a fire. I did it to prove the problem only... Dryer works well again and we will probably get another 5 years out of it!

Al
[email protected]

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

pushed the broken catch into the door and snapped the new one back in. Works perfectly!

NOTE: Please make sure the dryer is un-plugged any time you are reaching into the access panel with your hands or a tool. There are exposed connections everywhere. After using the diagnostic testing instructions (usually attached to the inside of the front panel) I determined it was a faulty Thermal Fuse. The PartSelect video instructs you to take half the dryer apart to access the Thermal Fuse, but I found it easy enough to just access it with the front panel removed. I used a small 1/4" drive socket to remove the single hex head sheet metal screw holding the Thermal Fuse in place. I then slid the 2 wires off, noting which went to which lug. Installed the new thermal fuse and after starting the screw by hand, tightening with the small socket wrench. It is a bit tricky to reconnect the wires as you are doing it all by feel, but it's a lot easier than taking half the dryer apart. Also, make sure you check the exhaust path for obstructions, that might be why the ThermalFuse blew in the first place.