CADG265RBL Whirlpool Dryer - Instructions

Pulled the top of dryer off. Separated the door from the drum seal or gasket, slipped the belt through, put the drive belt on the motor and then put it all back together.

The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.

Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.

Removed Two screws took out the coils put in the new ones
I ordered one day and got them the next day. Thank you partSelect For the quick service.

Unplugged dryer, and removed vent hose. Tilted dryer back, unscrewed 2 screws on lower front panel. Removed 2 screws on coil holder (needed a short screwdriver). Unhooked wiring harnesses from coils, and removed coils. everything in reverse for installation.

Replaceing only this item fixed my problem
with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on.
Note gas dryers are supposed to light, heat up, igniter stop flame stop after it gets up to temp, shut off for a while then repeat the process, it would have saved a lot of time researching to have known that earlier.. Take front panel off screws off, take panel off holding the 2 round coils in place, unplug the one with 3 prongs and replace, tested dryer with the panel off and the door closed so there was no suction issue. put panel back on 5 minute fix if you knew what you were doing.

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

took off bottom access panel replaced both electronic coils web site helped diagnose problem

I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own dryer. The dryer works perfectly now and gets very hot!

I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.

super easy 2 screws and my 11 year old son took 5 minutes.

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

First I removed the two screws that hold the front access panel. After taking an ohm reading on the coil I found it was an open coil. I went on line to find out where to get the part. PartSelect web site was very complete when I enter the part number. I was able to make the purchase on line. The part was stock and it arrived in 3 days without any special handling. I then unplugged the solenoid, removed the two screws that hold the coils on. Replaced coil and bracket .Tested the dryer and it was working properly. Installed the front panel. PROJECT COMPLETE!!