DCSR473GV1AA Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Palos Hills, IL
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer would heat up at start then go cool
Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from ERIE, PA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove plastic and insert
inserted the lint catcher into the opening to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Chanhassen, MN
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The control switch broke off flush from the start switch
My wife was attempting to start a load of laundry when the start knob came off in her hand. I figured the inside of the knob had broken loose and the stem from the rotary start switch would be sticking out, well the stem had broken off flush and the knob was fine. After ordering a replacement, I jerry rigged the broken one with a large screw driven into it and put it back in place, worked great, just had to put a screwdriver into the screw and turn it to get the dryer to start. I felt it was fine to stay that way but the wife insisted we install the new one to put the knob back in place. The new switch arrived very quickly and went into without a problem, just four screws to remove the panel, two wire connections and was working again.
Was this instruction helpful to you?
Thank you for voting!
Stem of Rotary Start Switch broke off
Fairly simple. removed start wwitch by rotating it out of its position. There is realy only one way to remove it and it is intuitive. The new part is simply placed n the only position that the part will fit in the panel. Once the part is locked in placed, the new part is installed. Simply take you time and think it thru.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from COMSTOCK PARK, MI
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing as drum rotated
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DERALD from Burleson, TX
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch was either stuck in start position or had to rotate full turn to start
Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LOVELAND, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LUMBERTON, TX
- Parts Used:
- WE03X37317, WE03X29897, WE12X83
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Belt broke
Removed drum replaced pulley attached pulley spring to catch on motor bracket put belt on drum put drum in aligned belt and pulley released. Spring replaced door and top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from WHITE LAKE, MI
- Parts Used:
- WE9M13
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket ripped
It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEMPHIS, TN
- Parts Used:
- WE18X25100, WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old dryer filter was cracked and bulb burnt out
Easy peasey! Just Removed/Replace screw-in type bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Clermont, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Selector knob broke off
I ordered a selector knob and it was delivered in a short amount of time. I wasn't sure if it was the right one when I ordered it, but my husband just put it right on the dryer. He said it was perfect. Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Garrison, NY
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
there was no problem
installation exactly how your directions told me on the computer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CHRISMAN, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
No flame. Igniter came on but no gas.
Opened up dryer for access to all components and tested. All checked good. Put back together and tested and igniter came on but no flame. Purchased two new coils and tested again. No flame. Purchased complete valve assembly and replaced old one. Tested again and viola, success! TY PartSelect for exact replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARIE from SAUGUS, MA
- Parts Used:
- WE05X20431, WE5M48
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Had to use y tube
After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!