DCCB330GJ0WC Whirlpool Dryer - Instructions

Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!

removed cover removed old coils installed
new coils ,test dryer running great .
thanks partselect.

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

UNPLUG Drier
Remove bottom panel 2 screw
Remove 2 connector to coil
remove 2 screws
lift off cover
lift coil s
reverse steps

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!

when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

easy as pie !

This turned out to be easier than I thought. I opened the access door on the front of the dryer after unplugging the dryer and turning off the gas. I reached in just inside the door with a short-handled phillips head screwdriver and removed the two screws holding the two coils in place. The screws were pretty tight and a bit difficult to get loose but after serveral attempts they finally broke loose. Once I removed the plate that covered the two coils they just slipped right off, much easier than I thought. I removed the electrical connections then attached the wires to the new coils and slipped them back on their respective pins. I reattached the "cover", then plugged the dryer back in and turned the gas on and started it up. The flame fired right up, much stronger than before I replaced the coils and of course the flame stayed on. Problem solved. Repair was really pretty simple with the diagnosis being the biggest problem.