HE2030 Whirlpool Dryer - Instructions

Installed the new part. Worked great!

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Just follow the video. The hardest part is getting the top to disengage from the clips.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

remove front part of the dryer and rise up the top to remove drum to replace the belt. than remove two screws for the heating element piece of cake repair.

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Took off the two lower front screws, Then the screws to take off the door and frame. Then the lint trap. Finally took out the drum. BOY WAS MY DRYER DIRTY WITH LINT! Vacumned it all out and washed the filter and filter housing with soap. Found out that I needed tension wheel also. Ordered that. Replaced the wheel, that was the hardest part. Need to take off this part like a "spring washer" and put it back on with the new wheel in place. Then placed the belt on the drum, belt on the tension, screwed the drum holder frame on, screwed the door frame on, screwed the lower panel on and it works great. By the way I am a female and if I can do it anyone can.

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.