CGD137SDW1 Whirlpool Dryer - Instructions

Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

Replaced Broken Belt and roller

Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.

Followed instructions supplied ( very easy)

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

it was easy all the parts were the exact replacement

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.

Kit was easy to install and after making sure the drum gaskets were set right the noises ended.

Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

I did as your online movie said to do it. It is a big help and you can see that the belt, rollers and idler pulley is not a difficult job and you save yourself at least $100. Toughest part of job is putting back the nylon triangle things that hold the rollers on without breaking them.That is why I used the needlenose pliers. The triangle things that hold on the rollers have little tabs on them and I just gently pulled them outward and the triangles went right on.That repair kit from Whirlpool(builder of my Kenmore dryer)was a real bargain and everything fit perfectly. Bottom line is don't be afraid to try this repair. You will most likely succede. Go out to diner with the money you saved. Good luck, Mike

watched the online video on the Partselect site which was very informative and straight forward. replaced the belt, tensioner, and two drum rollers (all included in the maintenance kit, (along with small hardware parts)). put it all back together, and VIOLA!!!!!! super quiet like the day we bought it!!! Thanks!!!