NG7519 Whirlpool Dryer - Instructions

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

as described in video. Very well done. Thank you

I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own dryer. The dryer works perfectly now and gets very hot!

I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.

took off bottom access panel replaced both electronic coils web site helped diagnose problem

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

super easy 2 screws and my 11 year old son took 5 minutes.

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

check the coils first. parts shipped to house within 24 hours. 29 bucks with shipping!

The first time, I inserted the belt the wrong way. The drum turns a little bit then stops. The manufacturer does not give any instructions or drawings on their website on that particular model, only drawing of parts.I called the technical support department and they told me to call different telephone numbers in my area and repair technicians. Still no schematic and instructions.
The solution: I took the broken belt, put around the drum, measured it, the remaining slack, did some trial and error around the motor axle and the pulley.
Placed a 2 X 4 piece of wood to hold the tension of the pulley. With the belt around the drum, carefully inserted the drum downward. placed the belt starting from the left side of the drum to the bottom of the motor axle, around it then to the bottom of the tension pulley, then towards the right side of the drum.
Lift the drum to its proper position, horizontal. Remove the piece of wood. Turn the drum manually so it moves freely. check the belt moving around the axle and the pulley. Install back the panels and screws tightened. Test and observe a few drying runs.

This would be an easy job, if I were to do it again.

I needed to download a manual only to get ACCESS to the machine. Removing the outside lag bolts did NOT provide access.

They had hidden clips that were ENTIRELY invisible from the outside. I believe this was done deliberately, to prevent those who don't know the specifics about this machine from gaining access.

It's an easy job, once you know the idiosyncracies of the construction of the machine. It's a major pain in the ass if you don't, even if you are used to replacing belts in other dryers.

Having done it once, the next time I could do it in under 20% of the time it took me the first time.

Basically, Followed the instructions in the Video for Belt replacement. I found out however that the Tensioner was also broken aand needed replacement, and this required the snap wring pliers. also spindle on motor was stripped and had to use "lockTite" to repair that. Overall was far better "doining it myself" than paying for repai service which would have cost several hundred $ in costs. This increased my confidence level to know that as long as parts are available I will always be able to repair this appliance!

First I removed the two screws that hold the front access panel. After taking an ohm reading on the coil I found it was an open coil. I went on line to find out where to get the part. PartSelect web site was very complete when I enter the part number. I was able to make the purchase on line. The part was stock and it arrived in 3 days without any special handling. I then unplugged the solenoid, removed the two screws that hold the coils on. Replaced coil and bracket .Tested the dryer and it was working properly. Installed the front panel. PROJECT COMPLETE!!