NE4313 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DOUG from GRESHAM, OR
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The dryer wasn't drying quick enough.
removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from richmond, KY
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
dryer has been making a squealing noise when it was started
To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryan from lewisburg, TN
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
loud squeaky sound
remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Saginaw, TX
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
unit stop heating
once I found where the heat element was, it took me a few mintues to remove the bad one and replace it with the new one that came before the due date. very good instruction in kit. Be sure and leave the old one hooked up until the new unit comes in so you can do a easy exchange of the wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Thorntown, IN
- Parts Used:
- WPY54414
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench set
Idler Pully squealing
removed bottom panel.Has 2 screws on bottom.take belt off of idler. take 2 screws out of motor base.turn motor sideways& remove bolt from arm that holds idler. remove snapring holding idler. replace pully & reassemble in reverse. Thank You Partselect for prompt shipping. A+ Rating
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Kremmling, CO
- Parts Used:
- WPY54414, WP40111201, WPW10121334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Broken belt and idler pulley.
I followed the belt replacement video and voila, the job was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from cathlamet, WA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
a pencil jammed the drum and broke the drive belt
remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Spring Valley, WI
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
pulley broke and belt
removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Azusa, CA
- Parts Used:
- WPY54414, WP23748, WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer was noisy. Sounded like loud squeaking noise.
Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ian from Greeley, CO
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Brighton, CO
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
old bearing disintegrated
clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Sublette, IL
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken belt
Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from NEPTUNE, NJ
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drum would slip and at times not spin
You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M from Noblesville, IN
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no heat
removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Palisade, CO
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
drum not turning properly
as described in video. Very well done. Thank you
Was this instruction helpful to you?
Thank you for voting!