DDC4500SBM Whirlpool Dryer - Instructions

went on line to look up the problem troubleshooting a maytag gas dryer. after checking different sites I figured that I needed a coil valve. searched for the part I needed and found the best deal on this site. I ordered the part and and by following the directions. I was able to replace the part on my own.

Installed new coil, helped but have other issues that I'm troubleshooting.

replace two heating coils. Dryer working find.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

DISCONNECT THE POWER. (I got shocked a few times during the diagnoses stage). Remove the lint catcher. Pop the top of the dryer up (there are two plastic tabs along the front of the dryer. Remove the two screws for the lint catcher and open the top of the dryer. Loosen the screws between the side and front panels. Lift up on the front of the dryer to free it from the clips down below. Swing the front panel out of the way to avoid disconnecting the door-open-switch. Undo the two screws holding the bracket onto the gas burner regulator. Replace the coils. Reassemble in the reverse order. It was helpful to open the dryer door to help align the drum and front panels.

1st replaced limit thermostat because it tested bad; this did not resolve the problem. Initial burn was successful. Heating element would heat but burner would not ignite for subsequent burns unless allowed to cool down for 10 minutes or more. Coils tested at correct values, but a u-tube video said that was not always an indication of a flawless coil set. It was either the coils or the burner itself. Burner would not have been a justifiable expense even though it came with new coil set, so tried the coil set, and it resolved the problem.

popped top up with flat screw-took out 4 screws (2 screws-1/4" nut driver - 2 phillips screws on bracket that holds coils in place) unplugged 2 wire lugs (1 three wire & 1 two wire) changed out bad coils screws back in-plugged wires back in -popped top back down .done

The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.

Well, had I read more of the reviews on this website, I would have learned that my problem was the valve coils. Instead, I assumed it was the igniter, so I ordered and installed a new igniter to no avail. I was about to just go buy a new dryer at Home Depot and spend $600, but I had to try again so I read more reviews on this website and began measuring resistances across the valve coils and discovered I had a bad one. I ordered both just to be safe, and installed them and quickly enjoyed my first uninterrupted dryer cycle in over a year (for over a year, I had been stopping and restarting my dryer about 10 times for each cycle). So THANKS for this website and to all the home technicians who posted symptoms, resistances, and how-to-do-its to help me get this done. It was an empowering experience to fix this and have bookmarked this website for any future appliance fixes. It's a great website with all its schematics and postings.

First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.

Followed directions from Youtube video

I follow the instructions provided on the your web site, the instructions were very easy to follow and to the point. In all it easier than expected. your information regarding the probability that the indicated part will solve the problem are great! That gave me a good feeling about ordering the part from you. Thanks for your help.

rts came quickly & I got started. First, I unplugged the dryer and pulled it away from the wall about a foot. this was done so the top would have clearance when it was lifted up. Next, I removed the lint trap and then took the two screws under the lint trap door out. Then you use a screwdriver(flat blade) to release the top of the dryer. The release points are about 1-2 inches from the edge of dryer. Next pull the wire connector apart so the front can be removed. The connector is on the right side, front corner, facing the dryer. There are two hexhead screws near the top on both sides. Remove the and the front will come apart as you lift it slightly. Then you disengage the tub belt. Once this is done the tub can be lifted out and set aside/ take care to remember each things position as you take it apart, so you will not get confused when you reassemble. Now the solinoid assembley is easy to get to. Use a phillips screw driver and remove the two screws that retain the bracket that holds the solinoids in place.. Lift the bracket and remove one solinoid at a time. Pull the wire from it and plug the new, like solinoid to the wire and put it back in place. then do the other one. set the bracket back over the new kit and replace the screws to the bracket. Set the tub back in, rethread the belt to the drive wheel. Next put the front back on making sure the bottom part slips into the two sides of the dryer.Replace the hexhead screws on each side; plug the wire connector together. Now , pull the lid down into position and press into place. Replace the lint trap screws and replace the lint trap. Plug dryer up and we are done. Repossition the dryer to its original place. It really was not a hard job at all. Thank-you Susan for your help and expertise.

Open top of dryer, then remove front. Coils on lower left. Unplug and replace coils. Vacuum loose lint from bottom of dryer. Replace front then top of dryer. Test run. All good !

Removed the screws on the dryer vent and the back of the dryer top. Then I raised up the top panel and removed the screws that held the front panel on. I removed the front panel to access the coils. I replaced the coils and then the front and top panel and screws. All went well. The dryer is working properly now.