NG5319 Whirlpool Dryer - Instructions

popped top up with flat screw-took out 4 screws (2 screws-1/4" nut driver - 2 phillips screws on bracket that holds coils in place) unplugged 2 wire lugs (1 three wire & 1 two wire) changed out bad coils screws back in-plugged wires back in -popped top back down .done

replace two heating coils. Dryer working find.

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.

The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.

I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

Checked ignitor it was working ok, disconnected 3 pronged coil and disconnected 2 pronged coil using multi tester checked continuity on both coils both tested 0,with help of operator ordered M Series new style coil kit. When parts arrived installed coils attached wire harnesses installed bracket and 2 screws that secures coils. Started dryer it worked and stayed working who needs the Maytag Repair Man probably saved about 200.00 between service call and markup on coils. Thanks Virtual Repairman

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

First I shut off the gas supply (the valve is an in-line shut-off and it's right there. I removed both of the retaining screws and detached the gas supply line.

Remove hte valve from the mounting plate (two more screws) and then reversed the process to replace the part.

It works just fine, thank you very much!!

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

The front panel was taken out and the parts were replaced. After the replacement, the drying time went back to the original 30-40 minutes.

Followed video on PartsSelect website, they made it real easy.

1. Unplugged from wall, turned off gas and opened top cover. 2. Removed two wire clips for door switch and unscrewed front cover (2 screws inside). 3. Removed front cover and moved to side. 4. Unplugged connectors from coils. 5. Unscrewed coil screws. 6. Replaced coils and tightened screws. 7. Replaced front cover, tightened screws and reinstalled wire clips. 8. Closed top cover, turned on gas and plugged in power. 9. Dryer fired right up and made heat.