WED5050LW0 Whirlpool Dryer - Instructions

Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Followed instructions supplied ( very easy)

Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

I watched the video online in the order section. then just did it after we received the repair kit.

Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.

Replaced Broken Belt and roller

Ordered a parts kit with belt, tensioner, rollers, & clips, but did not use. Unfortunately, the kit was not correct for this model, regardless of the sales reps assurances. The kit had two rollers, our unit has four. The belt tensioner was not even close to being the same. However, a thorough cleaning of the interior with vacuum and rag was done. Removed, cleaned, and lubed each of the four rollers and the tensioner wheel as well. Lubed with small amounts of sewing machine oil on the axles and light spray of silicone on plastic to plastic contact points. Voila! It's as quiet as new.

Took the back off of the dryer and diagnosed the problem. When I saw that the belt was broken I got online and looked for a place to find a replacement. Found Partselect.com and checked out their site and not only did I find the right parts but I also found a video detailing the repair. I purchased a maintenance kit (the belt, the wheels, and the hardware) and the next day my parts arrived and I was able to get the dryer back together in no time at all.

I assumed the drum belt has broken so without looking and tearing into the dryer first. I looked at the model number on parts select and the belt was $43.00. However the maintenance kit wihich included the belt, 2 wheel guides and belt tensioner was only $25.00. go figure. Ordered it and within 3 days it was at my front door. After opening the dryer I noticed the belt was intact. After removing the drum I notice heavy resistance on the motor. Thinking motor bearings were out! The internal motor heaters would drop out and than reset. Opened the fan shroud and found that a sock had fallin into the top lint screen opening and locked up the fan wheel with out the persons knowledge when the screen was than pushed back into place. Alot of work to find out something so simple. hilarious actually. What a relief that it was not the motor and since I had it apart I went ahead and put in the entire maintenance kit anyway. The whole ordeal toless than 1 hr.