NGD5800DW1 Whirlpool Dryer - Instructions

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

First disconnect power to the machine. Remove lower access door locate the igniter connector and disconnect it. Now, remove the screw holding the igniter to the mounting bracket with a 5/16" box wrench, carefully remove the igniter. Replace the old mounting bracket but first start the igniter mounting screw in the new bracket, threading it in all the way and then removing it to make installation easier. Install the new bracket and then the igniter, Be very careful, the igniter is fragile. Holding the igniter securely, install the mounting screw. Reconnect the wire connector replace lower door and plug the machine in. Voila! heat!!

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Ordered thermal fuse and cycling thermostat

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from over time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.