DCSR483GA2WW Whirlpool Dryer - Instructions

I was cleaning my laundry room when I noticed the gasket needed cleaning. While wiping it off it appeared as though I could remove it and that was my biggest mistake. Once removed it could not be replaced, due to the little parts that held it to the door began tearing off as I tried to put it back on. I ordered a new gasket and had it put on. It did not require any tools, just concentration. I've learned "if it's not broken, don't fix it"! I spoke with several other people and I am the only one who has removed a gasket. Thank you very much PartSelect for your help.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Both parts arrived quickly and were exactly what I ordered. The lint screen replacement part was of higher quality and it works better than the one that came with the dryer. Very satisfied.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

Took the few screws out replaced the part then put it back together.

I received the part in record time.(2 days) I had a little trouble getting the case off of the dryer, but the part was real easy to install. I have changed these before with another company and their instructins were not good at all. Your instruction were relly easy to understand, step by step.

Thanks

took out broken filter and replaced with new lint
filter.

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

Pulled off old knob put on new one

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!

First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Removed the broken handle from the dryer and popped on the new one.