HE2430 Whirlpool Dryer - Instructions

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

Removed the 2 screws from the bottom of the front panel and pulled the cover up and out. Labeled the wires to the light and door switch and disconnected. Lifted the belt tensioner arm and unlooped the belt from it and the motor. Removed the 4 bolts that hold the front drum support on then held the drum up and removed the support. Pulled the drum out slightly and allowed the rear to drop, at this point you can get to the rear rollers without pulling the drum out of the machine. The roller shaft was so tight I had to put a straight-blade bit in a 1/4" socket to get enough torque to break it loose. Make sure to use a large enough driver or you will strip the slot out of the screw. This model had a nut on the back but I was able to just drag my finger against it to get it apart. Removed the washer and roller from the shaft and cleaned the shaft and washer with WD40 before reinstalling with the new roller. Vacuumed all the lint I could get to and reassembled, lift drum, push back, front support, 4 bolts, belt, wires, front panel, 2 screws.

Just follow the video. The hardest part is getting the top to disengage from the clips.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

Followed video on PartsSelect website, they made it real easy.

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you