NGD4705EW0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
How to un-screw the blower fan!
The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.
To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjustable wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.
Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.
To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjustable wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.
Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.
Was this instruction helpful to you?
Thank you for voting!
dryer would not turn on
checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your website and the promt efficient service
Was this instruction helpful to you?
Thank you for voting!
Motor would not turn
1) Removed top of dryer
2) removed belt and drum
3) removed front of dryer
4) popped clips holding down motor
5) unscrewed rear fan from motor (by exposing and holding fan)
6) changed motor
7) changed support rollers and idler pully
8) reassemled dryer
2) removed belt and drum
3) removed front of dryer
4) popped clips holding down motor
5) unscrewed rear fan from motor (by exposing and holding fan)
6) changed motor
7) changed support rollers and idler pully
8) reassemled dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracie from Culver City, CA
- Parts Used:
- 279311
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
dryer worked but no heat
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Novi, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heat Would Not Come On
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda from Syracuse, NY
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dryer sounded like I was strangling a dog
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Piece of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manolak from MURFREESBORO, TN
- Parts Used:
- W10861521
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Was this instruction helpful to you?
Thank you for voting!
dryer had no heat, all other functions worked
After replacing the heat element as a guess, (which did not fix it), I measured voltage with a DVOM, found lower cut off switch in op, And thanx to some tips on parts select I ordered the the Thermal cut off kit, fast shipping, installed very easily and all is working properly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hamilton, OH
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaky Dryer
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from CAPE CORAL, FL
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer continued to run with door open
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bristol, CT
- Parts Used:
- W11778253
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
part number was different from the original, but it fit just fine.
installed the new dryer lint screen, it fit perfectly
and is now in operation.
and is now in operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Brentwood, CA
- Parts Used:
- 8541503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Placing Dryer on Top of Washing Machine with Stack Kit
I purchased a stack kit from "Part select.com". The item was just what I needed to do the job. The delivery of the part was made the next morning. WOW! Excellent service! The process was completed in less than 24 hours, start to finish. Very impressed!
Was this instruction helpful to you?
Thank you for voting!
Loudly clunking clothes drum due to worn out roller
Followed video on Parts Select site for comparable model showing roller and drive belt replacement.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
The triangle plastic retaining clips were the most difficult part , to put
on and take off. They required careful , firm stretching with needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!
Loud banging noise when running dryer
Found one of the two drum support rollers was badly worn. Found Partselect.com, found my parts in less then 2 mins. Figured that I was in there so I should just replace the belt so I got one of those also. Parts arrived in 3 days dryer as good as new in 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glencoe, IL
- Parts Used:
- WP694089
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dead motor
1. Shut off gas and disconnected dryer.
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap.
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
2. Opened cabinet. Easy sheet metal screws and fairly obvious how everything goes together. NB: You'll need a block (or a helper to hold things while you run to look for one) to hold the drum while removing the front.
3. The motor is connected with a single harness, so wiring is a snap.
4. Removing the blower wheel from the back was hard. I braced the motor shaft and turned with all the leverage I could muster, but it was stuck. Plan B: Recip saw to cut the shaft. Motor comes out one side and the fan comes out the other.
5. The fan, of course, was unusable because there was still a piece of motor shaft stuck in the thread. This is why I had to spring for a new wheel.
6. Put everything back together and receive wife's adoring praise...
Was this instruction helpful to you?
Thank you for voting!