DDC4492AGL Whirlpool Dryer - Instructions

Removed Two screws took out the coils put in the new ones
I ordered one day and got them the next day. Thank you partSelect For the quick service.

Replaceing only this item fixed my problem
with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on.
Note gas dryers are supposed to light, heat up, igniter stop flame stop after it gets up to temp, shut off for a while then repeat the process, it would have saved a lot of time researching to have known that earlier.. Take front panel off screws off, take panel off holding the 2 round coils in place, unplug the one with 3 prongs and replace, tested dryer with the panel off and the door closed so there was no suction issue. put panel back on 5 minute fix if you knew what you were doing.

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

Used your sites diagnostic questions to determine that the gas coils were the most likely cause for no gas ignition. Ordered parts. Followed general directions from your web site....very helpful. Disconnected electrical chord. Removed lower dryer panel. Removed two bracket screws and bracket that held coiles in place on top of gas valve. Disconnected electrical clips and removed coils.....note that one coil is inverted as compared to the other. Cannot confuse as the electrical connectors are different. Slid on new coils, replaced bracket, carefully replaced screws. As space adjacent to coils is tight, be careful in tightning screws so as to not strip heads. Connected coil electrical clips. Plugged in dryer electrical cord. Tested dryer by starting up. Success, gas ignition. Cleaned out dust/lint on the inside of the dryer cabinet before closing up.

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...

took off bottom access panel replaced both electronic coils web site helped diagnose problem

super easy 2 screws and my 11 year old son took 5 minutes.

I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own dryer. The dryer works perfectly now and gets very hot!

I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.

Actually, my boyfriend did the repair by taking off the top and back of the dryer to access the drum and belt he replaced the belt and put the dryer back together
We are greatful for your service and really happy we didn't have to drive all over to find the part.

Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.

check the coils first. parts shipped to house within 24 hours. 29 bucks with shipping!