7MMGD6630TM0 Whirlpool Dryer - Instructions

I had my laptop next to me and paused the tutorial video
as I did each step to chnage the drum rollers, idler pully and belt. Dryer runs great with no more screeching!

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.

I did as your online movie said to do it. It is a big help and you can see that the belt, rollers and idler pulley is not a difficult job and you save yourself at least $100. Toughest part of job is putting back the nylon triangle things that hold the rollers on without breaking them.That is why I used the needlenose pliers. The triangle things that hold on the rollers have little tabs on them and I just gently pulled them outward and the triangles went right on.That repair kit from Whirlpool(builder of my Kenmore dryer)was a real bargain and everything fit perfectly. Bottom line is don't be afraid to try this repair. You will most likely succede. Go out to diner with the money you saved. Good luck, Mike

watched the online video on the Partselect site which was very informative and straight forward. replaced the belt, tensioner, and two drum rollers (all included in the maintenance kit, (along with small hardware parts)). put it all back together, and VIOLA!!!!!! super quiet like the day we bought it!!! Thanks!!!

I watched your video that showed me how to remove the top then the face of the dryer. I then removed the drum and belt,after which I could then remove the support wheels and the belt tension wheel.I replaced the support wheels and tension wheel,the hardest part was removing the little plastic locking keepers that hold the support wheels in place. After that I was able to reinstall the drum with the new belt and reinstall the face and top of the dryer. My 15 year old dryer works great just like new. Thanks

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

Very detailed instructions.

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Viewed online video and written instructions that were included in maintenance kit.

Followed the procedure outlined in instructions included with maintenance kit. My dryer did not have a pully wheel on the idler arm. Instead it was more or less a wear bar formed in a semi circle attached to the idler bar. This is what was causing the noise. The dryer wheels were good and the dryer belt was good too after 10 years of use. The parts in the kit were of good quality and fit perfectly. The supplied instructions were easy to follow.

Poped the top; removed the front of dryer; removed the drum; replaced the rollers and clips, new belt, and new idler pulley. Cleaned out all the lint. Reinstalled all. It works perfect. Ordering the parts was easy and the assistance you give in diagnosing the problem was excellent.

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

I simply followed the instructions, replaced the belt, tub support wheels and tension pullie. Could not have been easier. I figured it was worth $47.00 to buy the kit and if it was another issue, at least I saved money vs. a service call. There are only so many things that can go wrong and the belt was the fix. 20 yr old dryer works just like new.