DDC4498AJL Whirlpool Dryer - Instructions

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.

replace two heating coils. Dryer working find.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

DISCONNECT THE POWER. (I got shocked a few times during the diagnoses stage). Remove the lint catcher. Pop the top of the dryer up (there are two plastic tabs along the front of the dryer. Remove the two screws for the lint catcher and open the top of the dryer. Loosen the screws between the side and front panels. Lift up on the front of the dryer to free it from the clips down below. Swing the front panel out of the way to avoid disconnecting the door-open-switch. Undo the two screws holding the bracket onto the gas burner regulator. Replace the coils. Reassemble in the reverse order. It was helpful to open the dryer door to help align the drum and front panels.

Installed new coil, helped but have other issues that I'm troubleshooting.

popped top up with flat screw-took out 4 screws (2 screws-1/4" nut driver - 2 phillips screws on bracket that holds coils in place) unplugged 2 wire lugs (1 three wire & 1 two wire) changed out bad coils screws back in-plugged wires back in -popped top back down .done

I follow the easy instruction by a user in your web site to reach the problem area and discoverd the drive belt was broken.
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand that lasted 25 years: GE

The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.

I unplug the electric, close the gas valve, use the putty blade to prize up the top,unplug the electric horness, took the front door off, took the anker plate off the two coils, removed the wire from each coil,be careful not toget the wires mixed up one coil has two proms and the other has three proms after that u put everything back together the way u took it off!!

Watched video instruction, paying attention to what it showed in machine. Several virsions of similar designs over the years, look over yours and note access points, take pictures as you go! Just pay attention, it is very logical. Spread the side panels to get the drum in and out, and pay attention to drum axel in back and the bushing it rides in. Be patient, be firm but gentle, no real forcing needed if you are alligned. Be sure the grooves of belt are on the drum, drive wheel on motor, no twists. Reverse order to reassemble. There are several internet videos of models with same basic setup, so look at others if one doesn't show the detail you need to see, or clear some uncertainty. Your local hardware to sorce push fastening for the idler wheel to shaft if you mash it up, they are cheep and several styles will work.

Moved the dryer so I had room to work. Took off front of dryer with torx socket. Took off drum belt then able to take out the drum. The glides were worn replaced with two new glides (held in with 5/16 screws). While apart replaced the heater assembly and replacement of the drum belt. Went very well and smooth.

Unplug power. Remove the lint filter and remove the 2 screws under the lint cover lid. Use flathead screw driver to pop off the top of the dryer housing. The clips are located at the front two corners.Just wedge and lift up to unclip. Remove two hex head screws on each side disconnecting the side housing from the front housing. Disconnect the wiring harness at the front top right side if you are facing dryer. Lift up on the front housing to unclip the bottom of housing. Just lift up and pull housing face toward you at an angle. The circular dryer piece where clothes go into will be loose but still attached. It will sag down a little. Then on bottom left side unscrew two screws to remove the 2 coils. You will need a stubby phillips screw driver about 1.5" long and you will need to lift up on the dryer circular piece out of the way a little. Once you remove the crews, remove the clip holding the two coils. Remove the wiring from the coils. 1 coil has two leads and one has 3. Replace one at a time just in case your model is slightly different. Be sure to install the coil with the little knobby part up and in alignment for when you reinstall the clip/ bracket that holds it in place. Replace the coils and install the racket/ clip with 2 screws. Reinstall the wires. Reinstalling the front face of dryer housing is a little tricky because you have to slide the bottom back onto the clips while holding the circular dryer part up. Then push the front housing up against the circular piece so they are aligned and fit. While holding it, screw the two hex screws on each side. Then reconnect harness and snap the top housing back onto the front face housing clips. Reinstall the two screws at the lint trap. Reinstall the lint trap and plug back in. The dryer is now fixed if that was your problem. Its a fairly simply job once you start doing it. Good luck.

I follow the instructions provided on the your web site, the instructions were very easy to follow and to the point. In all it easier than expected. your information regarding the probability that the indicated part will solve the problem are great! That gave me a good feeling about ordering the part from you. Thanks for your help.

rts came quickly & I got started. First, I unplugged the dryer and pulled it away from the wall about a foot. this was done so the top would have clearance when it was lifted up. Next, I removed the lint trap and then took the two screws under the lint trap door out. Then you use a screwdriver(flat blade) to release the top of the dryer. The release points are about 1-2 inches from the edge of dryer. Next pull the wire connector apart so the front can be removed. The connector is on the right side, front corner, facing the dryer. There are two hexhead screws near the top on both sides. Remove the and the front will come apart as you lift it slightly. Then you disengage the tub belt. Once this is done the tub can be lifted out and set aside/ take care to remember each things position as you take it apart, so you will not get confused when you reassemble. Now the solinoid assembley is easy to get to. Use a phillips screw driver and remove the two screws that retain the bracket that holds the solinoids in place.. Lift the bracket and remove one solinoid at a time. Pull the wire from it and plug the new, like solinoid to the wire and put it back in place. then do the other one. set the bracket back over the new kit and replace the screws to the bracket. Set the tub back in, rethread the belt to the drive wheel. Next put the front back on making sure the bottom part slips into the two sides of the dryer.Replace the hexhead screws on each side; plug the wire connector together. Now , pull the lid down into position and press into place. Replace the lint trap screws and replace the lint trap. Plug dryer up and we are done. Repossition the dryer to its original place. It really was not a hard job at all. Thank-you Susan for your help and expertise.