NE3513 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Lakewood Village, TX
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken Idler pulley
removed front, top cabinet, drum, belt and motor. replaced idler pulley on motor. replaced motor, belt, drum and cabinet parts. test ran fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Newt from Daphne, AL
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dryer would not come on
When the dryer stopped working, I checked the two switches to see if they were good. The start button checked out OK but the switch on the door read bad. Ordered the part with the part number and put on when it arrived. Just a matter of disconnecting and reconnecting three wires. Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garold from Bothell, WA
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken belt
I don't have the model number right now, but you video was fantastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from minooka, IL
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer was making a real loud grinding noise, like nails on a chalk board.
Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminigildo from virginia beach, VA
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Belt cut in two
First I take off all front cover and then the dirt strainer next is the dryer drum holder next the top cover I lift up and so you room to set the dum belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Braunfels, TX
- Parts Used:
- 56000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wife let ink pin fall through lint trap and started dryer it broke fan.
Pulled off front of dryer because it made loud noise, lifted clothing drum removed cover for fan and order from model number on fan and replaced. 30 min with help from my son.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from st. louis, MO
- Parts Used:
- WPY54414, WPW10121334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
excessive squeeling noise
replaced idler puller and washers
Was this instruction helpful to you?
Thank you for voting!
Blower wheel broken and rubbing on housing.
Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Middletown, NY
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dryer did not tumble.....Loose ....worn Belt
Fast delivery,,,, Easy installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Shelbyville, KY
- Parts Used:
- WP40111201, W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Slipping drum, and broken door switch
Just like in the video. A very simple repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daral from Merrimack, NH
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Idle pulley frozen
Once I realized the drum was to be removed, the actual repair was not difficult. Because of the location of the pulley, it's best to tilt the dryer. Snap ring pliers are required to remove the retaining ring on pulley. I pulled the damaged pulley from the bearing. A small gear puller was needed to removed the frozen bearing. Lightly oil the new bearing. Installing the drum is a challenge because of the loose belt. I used paint tape to hold the belt on the drum. Download the service manual for good exploded parts views.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from Greenville, NC
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My dryer belt broke.
I took the dryer apart and used the video on the website that helped a lot on how to install the belt and then we put it back together and dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Marine City, MI
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Belt Broke
Watched the video from part select and it was easy. I will always order from part select, I loved the delivery time!! I ordered two belts, one for my dryer and one for my sons. . . My belt arrived the next day and my sons only took two days. . . Now that is service. . Thank you part select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from Shelbyville, MI
- Parts Used:
- R9900489
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The temperature in the dryer always got too hot even on low settings
I was ordering a part for my daughter who needed a high limit switch and a fuse, it occurred to me after reading the troubleshooting helps on PartSelect that this was what I needed to change on my dryer also. With the help of your installation videos my daughter was able to repair her own dryer and save about $150.00 and I too was able to repair my own dryer and now it works great! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Majid from Baltimore, MD
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The drying drum insde the dryer was not running
I openned the dryer and look for the problems. I found out the idle pulley was severly damaged. the driving belt was still ok however a piced of the belt backing was erroded. i found Part Select website and contact. The website is owsome! realy easy to follow and get youn to your needed parts. Customer service and the sales people are great. Also the video on the website is great and very easy to follow, they teach you how to install the parts. I had a very good experience with Part Select company. Thanks!
Was this instruction helpful to you?
Thank you for voting!