Models > AEM633 > Instructions

AEM633 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the AEM633
121 - 135 of 191
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
FRED from ELK MOUND, WI
Parts Used:
WPW10116735
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Dryer would overheat at all temperature settings
replaced the limit thermostat,thermal fuse, and cycling thermostat. Bingo. Problem solved. Noticed that the back of cycling thermostat had a buildup of lint and I'm wondering if that acted as insulation and caused a wrong reading of temperature. Did not have to disassemble dryer as I could reach all parts with lower front panel removed. To make it easer to install new parts with one hand I lightly hot glued the screws through the new parts and taped the upper portion of new part to bulkhead. With everything lined up and no need to hold the screws I was able to attach using one hand. It was a reach but easily done.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arthur from Lebanon, ME
Parts Used:
WPY54414, WP40111201, WP23748, WPW10121334
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
noisy
Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Wellsboro, PA
Parts Used:
WP40111201
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Replace drum belt
Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Pottstown, PA
Parts Used:
56000
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench (Adjustable)
The blower wheel was busted because somebody ran the dryer without the lint filter in. A cord and a fork were caught in it!
Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vickie from Lincoln, NE
Parts Used:
W10857122
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed a new grate where the water dispenses.
I just lifed the old grate off and layed the new one in.
0 of 226 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Garold from Bothell, WA
Parts Used:
WP40111201
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
broken belt
I don't have the model number right now, but you video was fantastic.
Was this instruction helpful to you?
Thank you for voting!
Customer:
mike from minooka, IL
Parts Used:
WPY54414
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
dryer was making a real loud grinding noise, like nails on a chalk board.
Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Herminigildo from virginia beach, VA
Parts Used:
WP40111201
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Belt cut in two
First I take off all front cover and then the dirt strainer next is the dryer drum holder next the top cover I lift up and so you room to set the dum belt
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eugene from Arlington, TX
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Door Latch broken
Ordered part ( door latch ) flowed instructions easily fixed same.
Was this instruction helpful to you?
Thank you for voting!
Customer:
aden from clearwater, FL
Parts Used:
511969, 56000
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Blower wheel broken and rubbing on housing.
Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Timothy from Middletown, NY
Parts Used:
WP40111201
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Dryer did not tumble.....Loose ....worn Belt
Fast delivery,,,, Easy installation
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Lakewood Village, TX
Parts Used:
WPY54414
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Broken Idler pulley
removed front, top cabinet, drum, belt and motor. replaced idler pulley on motor. replaced motor, belt, drum and cabinet parts. test ran fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
greg from phoenix, AZ
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the plastic latch broke
im a car mecanic it was easy
Was this instruction helpful to you?
Thank you for voting!
Customer:
jim from st. louis, MO
Parts Used:
WPY54414, WPW10121334
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
excessive squeeling noise
replaced idler puller and washers
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerry from New Braunfels, TX
Parts Used:
56000
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Wife let ink pin fall through lint trap and started dryer it broke fan.
Pulled off front of dryer because it made loud noise, lifted clothing drum removed cover for fan and order from model number on fan and replaced. 30 min with help from my son.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the AEM633
121 - 135 of 191