AEM633 Whirlpool Dryer - Instructions

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

I just followed the video instructions and really they were not as good as some of the customer descriptions which were far more detailed. It was like an experienced repairman telling another experienced repairman how he has been doing this repair for 20 years. The customers get into the kind of detail that is very helpful. More important parts select never tells you to read the blogs first before ordering your parts. $100 later I bought a new GE dryer which I would have done 10 days ago had I known Maytag has a repetitive problem with the high limit thermal fuse which no one has a cure for. So I did a whole bunch of repairs replacing parts on a dryer which needed to be replaced.

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely