DBB3300GA2WW Whirlpool Dryer - Instructions

Many have already described the repair, and it was exactly as they have described. Remove the two screws inside the top of the opening which hold down the top of the dryer. Pull off the top, and look inside to remove the two small screws that attach the front of the dryer. As the front separates, the front comes out of the drum and the drum bearing will come into view. Pop out the drum bearing ~ there are no screws ~ it simply snaps in place. (I suggest removing the lightbulb first, or you'll be buying one of those also. )

Replace the new drum bearing and snap it into place. Then replace the four drum slides. Replacing the drum slides is a quick, one minute task. Mine were completely worn away ~ no wonder it was squealing so badly. Then reverse the process to put it all back together. Total job was maybe 15 minutes long. Easy as could be and saved a ton of money, I'm sure. Sounds like new now!

Piece of advice that I could not find anywhere prior to ordering ~ you need FOUR drum slides to replace them all. Not knowing, I originally only bought two, so I had to order two more and add them later. Also, I probably could have gotten away without replacing the drum bearing ~ the slides were all that was really worn.

Thanks for the quick turnaround on the orders and the advice on line. Easy, easy, easy!

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Removed the broken handle from the dryer and popped on the new one.

Simply removed the cracked timer knob and replaced with the new one. The replacement time was received in less than 24 hours after I made the order! Outstanding customer service!

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

I replaced the old knob with a new one.

The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.

Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

unscrewed the back plate off of the dryer. Disconnected the the wires off of the switch. Remember to to unplug your dryer from the wall first!!!. Reconnect the wires to the new switch and twist back into place. Be careful not to bend the metal tabs. Put the back plate back on and plug in. Put on new knob and the wife was smiling. Took about 8 minutes to repair.

Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of the door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).

Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then he said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.

a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

snapped in new latch

I changed the two coils for the gas valve and the dryer is now working fine thanks

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.