DCXR463GA2AA Whirlpool Dryer - Instructions

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

Took the few screws out replaced the part then put it back together.

Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785.

Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!

Part select delivery is really fantastic (even though it took me three orders to get it right!).

took out broken filter and replaced with new lint
filter.

I received the part in record time.(2 days) I had a little trouble getting the case off of the dryer, but the part was real easy to install. I have changed these before with another company and their instructins were not good at all. Your instruction were relly easy to understand, step by step.

Thanks

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

Unplugged the dryer. Took the four star screws out of the console top. Pull consoled forward. Removed the knob. Pull up the locking tap on the old timer and twisted the timer counter clockwise. Timer easily detached from its mounting plate. Changed one wire at a time from the old to the new timer. Replaced timer and knob and screws.
Works great.

Pulled off old knob put on new one

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

Many have already described the repair, and it was exactly as they have described. Remove the two screws inside the top of the opening which hold down the top of the dryer. Pull off the top, and look inside to remove the two small screws that attach the front of the dryer. As the front separates, the front comes out of the drum and the drum bearing will come into view. Pop out the drum bearing ~ there are no screws ~ it simply snaps in place. (I suggest removing the lightbulb first, or you'll be buying one of those also. )

Replace the new drum bearing and snap it into place. Then replace the four drum slides. Replacing the drum slides is a quick, one minute task. Mine were completely worn away ~ no wonder it was squealing so badly. Then reverse the process to put it all back together. Total job was maybe 15 minutes long. Easy as could be and saved a ton of money, I'm sure. Sounds like new now!

Piece of advice that I could not find anywhere prior to ordering ~ you need FOUR drum slides to replace them all. Not knowing, I originally only bought two, so I had to order two more and add them later. Also, I probably could have gotten away without replacing the drum bearing ~ the slides were all that was really worn.

Thanks for the quick turnaround on the orders and the advice on line. Easy, easy, easy!

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you