AE4113 Whirlpool Dryer - Instructions

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

removed old element, relaced with new element , thermostat dryer works better than it has in along time

Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.

Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.

removed front of dryer, replaced old pully and put on new belt.

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

Replaced Thermostat Boosting heater and Cycling Thermostat located behind the front blower cowling. I did not remove the wiring until I had the new part so that i could connect them in the proper order.

Too simple to describe.

Unplugged the dryer. Used the putty knife to release the spring clips. Opened the top and photographed then disconnected the wires at the top of the terminal block. Removed the old power cord and terminal block. Installed new terminal block. Reconnected wires according to pictures. Installed new power cord.

Pushed in the Door Catch, and it was fixed.