DBXR463GB1CC Whirlpool Dryer - Instructions

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

It was amazingly simple and I am not even a handy man by any means. The only difficult part was pulling the cable connections as they are a bit tight. I was glad that I could accomplish this task for which the repair person was demanding $120.
Most of these things are doable it's just that common folk are just too scared to even try them out. I figured rather than going out to buy a new dryer for $500 ( and if my wife had her way, $1000) I could give it a shot for $80.

The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

Took out interlock switch (two leads) and replaced with new one. As simple as that.

After reading comments made by other customers, I ordered the timer and it arrived 3 days later. I used a star bit with the electric screw driver to open the top of the dryer. I removed all the dials and pulled open the top cover of the dryer. I carefully lifted the "tang" that kept the timer in place and turned the timer clockwise. I then used my cell phone camera and took picutres of all the connections so that it would be easier to reconnect the wireing to the new timer. I disconnected the wiring from the old timer and reconnected them to the new timer. I inserted the tang place in place and rotated the time timer counter clockwise. I then placed the cover back on, inserted the star screws and tighten them down. I put back all the dails and the dryer is working perfectly since. Took about 30 mins. I'm very pleased with the delivery of the timer and the ease of the installation. I will use Part Select as my sole supplier for all future repairs on my appliances. Part Select is Number 1 in my book!!!!

Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.

This repair was the easiest that I've ever done. Removed 4 torx head screws on the back and the timer unsnapped from its holder. I unplugged one wire at a time and plugged each one to the new timer. This part came the next day after I ordered it and PartSelect was cheaper than any other supplier.

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

Replaced coils on gas valve.