DBXR453GA2WW Whirlpool Dryer - Instructions

My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

After reading comments made by other customers, I ordered the timer and it arrived 3 days later. I used a star bit with the electric screw driver to open the top of the dryer. I removed all the dials and pulled open the top cover of the dryer. I carefully lifted the "tang" that kept the timer in place and turned the timer clockwise. I then used my cell phone camera and took picutres of all the connections so that it would be easier to reconnect the wireing to the new timer. I disconnected the wiring from the old timer and reconnected them to the new timer. I inserted the tang place in place and rotated the time timer counter clockwise. I then placed the cover back on, inserted the star screws and tighten them down. I put back all the dails and the dryer is working perfectly since. Took about 30 mins. I'm very pleased with the delivery of the timer and the ease of the installation. I will use Part Select as my sole supplier for all future repairs on my appliances. Part Select is Number 1 in my book!!!!

Took out interlock switch (two leads) and replaced with new one. As simple as that.

It was amazingly simple and I am not even a handy man by any means. The only difficult part was pulling the cable connections as they are a bit tight. I was glad that I could accomplish this task for which the repair person was demanding $120.
Most of these things are doable it's just that common folk are just too scared to even try them out. I figured rather than going out to buy a new dryer for $500 ( and if my wife had her way, $1000) I could give it a shot for $80.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed

Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

This repair was the easiest that I've ever done. Removed 4 torx head screws on the back and the timer unsnapped from its holder. I unplugged one wire at a time and plugged each one to the new timer. This part came the next day after I ordered it and PartSelect was cheaper than any other supplier.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Replaced coils on gas valve.

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.